working against 5.99.44: AR8131/2 driver

[Ignatios Souvatzis]

added
#alc driver for Atheros L1E Gigabit Ethernet
alc* at pci? dev ? function ? # Atheros L1 Gigabit Ethernet (EXP)
atphy* at mii? phy ? # Attansic/Atheros PHYs
compile MONOLITHIC kernel
and commented out hdaudio becuase it causes my laptop to crashes
worked after running commands in test_alc.sh

For the record: with 5.99.43 MONOLITHIC, on the eeepc 1008HA, I only
get timeout reading phy registers. Lots of timeouts. And Status:
no network"., whether I use atphy or disable it with boot -c to
fall back to ukphy

-is


--
Posted automagically by a mail2news gateway at muc.de e.V.
Please direct questions, flames, donations, etc. to news-***@muc.de

[Ignatios Souvatzis]

Post by Ignatios Souvatzis
For the record: with 5.99.43 MONOLITHIC, on the eeepc 1008HA, I only
no network"., whether I use atphy or disable it with boot -c to
fall back to ukphy

20110129 0000 5.99.44 shows the same error. I'll append the dmesg output
below. Can you post your /var/run/dmesg.boot for comparison, please?

-is

[Ignatios Souvatzis]

I booted with alcdebug set to 1. Firecrow - can you do that, too, please?

On Wed, Feb 02, 2011 at 09:22:44PM +0100, Ignatios Souvatzis wrote:
...

ppb1 at pci0 dev 28 function 1: vendor 0x8086 product 0x27d2 (rev. 0x02)
ppb1: PCI Express 1.0 <Root Port of PCI-E Root Complex>
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
alc0 at pci2 dev 0 function 0: Attansic/Atheros L1E Ethernet
alc0: ioapic0 pin 17

alc0: Read request size : 128 bytes.
alc0: TLP payload size : 128 bytes.
alc0: PCI device revision : 0x00c0
alc0: Chip id/revision : 0xc002
alc0: 15872 Tx FIFO, 15360 Rx FIFO

alc0: Ethernet address 00:26:18:15:30:39
atphy0 at alc0 phy 0: L1 10/100/1000 PHY, rev. 11
atphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, auto

--
Posted automagically by a mail2news gateway at muc.de e.V.
Please direct questions, flames, donations, etc. to news-***@muc.de

[fire crow]

Post by Ignatios Souvatzis
I booted with alcdebug set to 1. Firecrow - can you do that, too, please?
...

ppb1 at pci0 dev 28 function 1: vendor 0x8086 product 0x27d2 (rev. 0x02)
ppb1: PCI Express 1.0 <Root Port of PCI-E Root Complex>
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
alc0 at pci2 dev 0 function 0: Attansic/Atheros L1E Ethernet
alc0: ioapic0 pin 17

alc0: Read request size : 128 bytes.
alc0: TLP payload size : 128 bytes.
alc0: PCI device revision : 0x00c0
alc0: Chip id/revision : 0xc002
alc0: 15872 Tx FIFO, 15360 Rx FIFO

alc0: Ethernet address 00:26:18:15:30:39
atphy0 at alc0 phy 0: L1 10/100/1000 PHY, rev. 11
atphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, auto

lost my current, partition, being my reckelss self, so I'll need to
set it back up to get those results,

but I did run into one of the error conditions you mentioned earlier
while putting it back together,

5.1_RC3 userland, 5.99.39 kernel - gave me those atphy0 timeouts, lost
of em and nothing else

+
| fire crow
| computer programmer
!_____________________

  http://firecrow.com, ***@firecrow.com, 917.306.9451, New York City, USA

--
Posted automagically by a mail2news gateway at muc.de e.V.
Please direct questions, flames, donations, etc. to news-***@muc.de